Відео

Wow $1100 for less then 400 ftlbs on that 3/8 i paid 150 for my dcf901 that hits that hard with 2 battery's...

The Ridgid cut off tool is one of the best on the market imo, and not only because it’s seemingly one of the most powerful but also because ime they can be found pretty cheap most of the time comparatively.

Nice video SC. Can’t wait to see how that new flex high torque fx1472 does on your channel. ATM Ohio power tool has it as one of the free gifts when you buy the 6ah stacked lithium starter kit so new high torque 1/2 or 3/4 and a 6ah stacked lithium pack as well as the 280w charger so that’s a solid deal on what appears to be a nice wrench. Just figured I’d share. Have a good one 🙏🏻✌🏻

Winding them on and giving them a few love clicks isn’t going to hold the wheel on

I think you need to push more - I noticed sds hammers are very ineffective if you do not push, as they hit so many times that the fork stays at the outer limit and no blows are occurring. If you brace the target, push into it with the hammer off (to the limit the sds bit will go) and then pull the trigger while pushing, the thing will produce way more force. In this video the target appears loose and that won't work

Thats why you use impact sockets, not reg chrome ones

All the rust dust

First thing let the gun run second where did you pay $700 bro they ripped you off

Impacts are usually Cromoly. I can see that impact you have says chrome vanadium. chromoly impacts are meant to flex more and are used by Snap-on , Wright, Koken, Proto and Cornwell among others. Usually chrome vanadium does not hold up to impacts very well. There are some much more expensive alloys that bigger companies will use to produce chrome vanadium impacts. Hazet and Gedore have special alloy chrome vanadium. Usually if youre buying very cheap impacts from China its best to go with Chromoly as they probably arent using a more expensive chrome vanadium alloy.

Don't know who you bought it from but no dewalt impact costs $700, try holding it for longer, and more firm to so it not giving kick back between socket and inpackt, use atleast 6amp bat. and maybe than itll work, this isn't tools fault but user fault, that it didn't work...

That is hilarious... Not rusted, nor destroyed. It did however do decent job loosening an axle nut.

Only 2 comments. When you gonna test the DCF961?

I would suggest not to tighten it with an impact, It happened to me that I had to rent a stronger/bigger impact wrench than what I normally use after I used it to tighten a crank bolt in a Toyota (even after I made sure just to put very few seconds of impacting); I learned this happens a lot in fine thread bolts, where the torque climbs rapidly when impacted; this can even damage the crank threads.

A decent drill driver would break it loose instantly wouldn’t it?

5:15 ... Oh shift :)

Learn to use the correct socket before you embarrass yourself

A female tutorial is not suggested to take seriously 😂😂

I put mine on with my dewalt and now I can’t get them off.

Are you on IG?

That ryobi sounds like there’s no grease in any of the bearings/gears etc or motor is dying

I bought this same impact wrench. I also bought the same size impact sockets but I can't seem to get it to fit on the device. It's a half inch impact wrench so I should be able to fit it in a half inch socket? What am I doing wrong?

Where do you work? Or you own a junkyard or?

That what was possible

Fucking rotor bolts. That's what I need mine for

Thanks!

Socket was turning only 2 seconds on a corroded nut wont do much

Bro just be walking around his neighborhood removing Lugnuts off his neighbors tires😂😂 he’s a menace

Dewalt been superior on job sites for a while.

Ive not ran across anything yet mine wont break loose even helped a guy that couldnt get his lug nuts off and it did it with ease

I just bought the DeWalt DCF891 with a single Power Stack Battery. Tool with battery should weigh 4.75lbs. My air Ingersoll Rand 2235QTiMAX is 4.2lbs + hose.

Crapman tool 😂😂😂

“Rusty” 🤣

I only listen to AM radio, the FM in my area is nothing but commercials. FYI, that antenna you see is only for FM.

One of the best reviews. Totally agree. Just put it to work and THEN go through it. Excellent

That swivel joint really robs torque

I got the 961 for less than half. 😂

What speed????

This video is for hype only! Dishonest blogger!

I need this gun asap

should unbolt it by the opposite

If you use an adapter to attach sockets on the DeWalt DCF787DT2 impact driver, is that essentially the same as the impact wrench? What I mean is, will I get more versatility out of buying an impact driver over an impact wrench? Is there essentially little difference? Thanks.

I did my gm 5.3 crank bolt with my dewalt 891 mid torque 🙃

Anyone looking to get that impact all I can say is get it. With the 5ah power stack it's got 2000lbs brake away. I use mine with my 12ah flex volt battery and I swear it's all of that. Easily the strongest impact in the heavy duty shop I work in. It scares everyone when it hit VTEC mode which is after like 4 seconds of it hasn't broken the bolt free it turns up the power in a very noticable way.

This is one of the best videos on UA-cam. Subscribe

Masterpiece video and thank you for not putting stupid music

It was already loose num nuts

Looks like you need to heat that bolt up after hitting it with an air hammer, then itll come right out

I love me my snap on impact, busts more nuts then I do